Do you find yourself trying to locate insight around How to Install a Bathtub?
Installing a bath tub isn't specifically brain surgery, but it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a new one is also a reasonably hard project. If the old bathtub is conveniently available, the job can move quickly; if you need to open up a wall surface to eliminate the old tub and position the new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will need a helper to leave the old tub and also embeded in the brand-new one. See to it you have actually qualified on your own for the job and fit attempting it. As opposed to employing a professional to take over a halfway-completed task, it is far better to think about employing one before you start. Opportunities are you may need a professional plumber to make tube connections.
This article will certainly assist you install a new bath tub in your shower room if you have currently purchased a brand-new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools and also material checklist must make up the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its final setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water supply and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has actually been used at the very least when as this will resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Safeguard the tap in place with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can break relatively very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very drawn to How to Install a Bathtub and I really hope you enjoyed reading the entire blog entry. For those who enjoyed our blog posting plz don't forget to share it. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Contact